The WM-10GMT-48N is a 1RU rack mount 10 position fused power distribution panel designed to use standard GMT ( Grasshopper Made for Telecom) Fuses. The WM-10GMT-48N provides front panel LED's to provide a visual indication of a fuse open condition and also DC power present. In addition Form C relay contacts provide a remote fuse fail indication. This power distribution panel is built for up to 15 Amps per fuse and 100 Amps per unit.. This model is built specifically for Positive GND installation.

DIN mount ATC-ATO fused distribution panel. The DIN-5-75 has ten positions at 20 Amps maximum per fuse. Has negative and positive bust bar for efficient power distribution for a maximum current of 75 Amps.

Features:

Access power for 5 outputs

For 12,24 and 48 volts DC Systems

Up to 20 Amps per fuse / 75 Amps Max

Includes dual (Neg/Pos) input terminals on each parallel "add-on" capability

Can be installed on DIM Rail TS-35/7.5 or 15

Requires ATC/ATO blades fuses (not included)

3 year warranty

The DBRM-15-75 is 2RU a rack mount 15 position fused DC power distribution panel designed to use standard ATC/ATO fuses. This power distribution panel is built for up to 20 Amps maximum per fuse for a maximum current of 75 Amps per panel.

The DBRM-10-75 is a 2RU rack mount 10 position fused DC power distribution panel designed to use standard ATC/ATO fuses. This power distribution panel is built for up to 20 Amps maximum per fuse for a maximum current of 75 Amps per panel.

The DBRM-20-75 is a 2RU rack mount 20 position fused DC power distribution panel designed to use standard ATC/ATO fuses. This power distribution panel is built for up to 20 Amps maximum per fuse for a maximum current of 75 Amps per panel.

Breaker Panel and Rack Mount.

Westell's 10-position,15 Amp Front-Access Single-Bus GMT Fuse Panel offers some of the industry's highest GMT amperages available in a rack-mount, compact and very cost competitive package. With 15 Amp fuses in a single bus, 70 Amp panel, it is a perfect fit for fused DC power distribution for applications with limited space. This Westell fuse panel features a wide operating voltage range (–24 or –48, polarity insensitive) and distributed output lugs, this panel exceeds the requirements of both legacy and Next Generation networks.

The NPGMT1107 Fuse Panel provides up to 20 circuits for the distribution of DC power to equipment. Each of the 20 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 10 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at the rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

The N250120-N/L9 Fuse Panel provides up to 20 circuits for the distribution of DC power to equipment. Each of the 20 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs ar e provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 10 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at t he rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

The NPGMT1012 Fuse Panel provides up to 30 circuits for the distribution of DC power to equipment. Each of the 30 circuits is individually protected by a GMT style telecommunication fuse (20A max) located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 15 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at the rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

The Westell N250140-NCY-M3 Fuse Panels provide up to 40 circuits for the distribution of DC power to equipment. Each of the 40 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 20 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at the rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage of fuse is to be used.

The Westell N250110-N/0803 Fuse Panel provides up to 10 circuits for the distribution of DC power to equipment. Each of the 10 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located on the front of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 5 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection on the front of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used. The panel is equipped with dummy fuses in all unused positions.

Alarm circuits are provided to alert service personnel of fault conditions. A fuse alarm is caused when any of the GMT distribution fuses opens. A red fuse alarm LED on the faceplate will illuminate and the Normal Operation LED will extinguish to signal a fuse alarm and also the appropriate MAJOR relay contacts will change states. The fuse panel has common (C), normally open (NO) and normally closed (NC) terminals for both Major and Minor alarms. A Major alarm being a fuse or power failure in that bus and a Minor alarm being an external alarm. The external alarm is ground activated (20mA required to activate alarm). Note, the use of the alarm contacts is optional, if you do not wish to extend the alarms, you don't have to do anything with the alarm pins.

The "Normal" condition of the relay exists when the panel is powered up without any blown fuses or externally activated alarms. The red External Alarm LED on the units face plate will light when a ground is connected to the MINOR "Alarm In" terminal (20mA max signal required to activate alarm).

The N250110-N/0803 fuse panel is made from 0.050" steel and painted off white. This panel is shipped with universal brackets that will fit both 19" and 23" wide racks and uses only one 1.75" panel spaces. The panel has two clear L shaped shields to protect the wiring connections on the front of the panel.

• Two isolated groups (busses) of 5 GMT fuses in each (15Amps/GMT position).
• Polarity insensitive (+/- 24 or +/- 48 Vdc) battery voltage (other voltages, see Ordering Options).
• This panel can provide 100 Amps of fusing per panel (50 Amps of fusing per Bus).
• This panel can operate at 66 Amps of output current per panel (33 Amps per Bus).
• Barrier terminal strips for fused outputs and isolated returns (grounds).
• Three sets of Form C relay contacts are provided to extend alarms.

Westell's latest GMT Fuse and Alarm Panel offers some of the industry's highest GMT amperages available in a compact and very cost competitive package. With 20Amp fuses in a dual 100Amp bus, it is a perfect fit for the applications limited on space. With standard Westell fuse panel features like variable operating voltage (Añ24 and Añ48) and cascading output lugs, this panel exceeds the requirements of both legacy and Next Generation networks.

Features

• Cost effective, compact design expanding applicationflexibility
• Two isolated groups (busses) with 10 GMT style fuses ineach (20Amps/GMT position and a max of 100Amps/bus)
• Two sets of Form C relay contacts are provided to extendalarms
• One set of alarm contacts for each; Bus A and Bus B Alarm
• Dual ground lugs meeting or exceeding carrierspecifications
• Universal voltage (+/-24/+/-48 VDC) offering network flexibility
• Screw-down lugs on both the inputs and outputs increasing reliability
• GMT fuse holders mounted for downward trip indication ƒ_" easier identification and detection of blown fuses
• NEBS level 3 verified, with zone 4 earthquake; UL Listed

The Westell N250120-N-L33 Fuse Panel provides up to 20 circuits for the distribution of DC power to equipment. Each of the 20 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located on the front of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 10 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection on the front of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

Protect your investment and safely power your systems with Newmar's fuse distribution panel. These fuse panels are ideal for DC distribution to low power loads in 48 volt positive ground network applications and provide enhanced system reliability via dual input buses, which allow configuration with redundant power sources.

Each input bus accommodates 10 GMT output fuses in ratings up to 15 amps. Front panel LEDs indicate normal operation, fuse failure mode, as well as a user configured external alarm signal.

The DIN-LVD-48 is pre-set to disconnect the load at 42 VDC. However, to prevent premature or false disconnect when the battery voltage drops below the 42-volt threshold a 2-minute timer is started. If the battery recovers to above 42 volts, the timer resets and waits. The battery can and will recover if the system is a repeater or remote base station or similar equipment that has a varying demand that fluctuates from low to high current. The 2-minute delay ensures the battery is not disconnected until necessary to prevent damage.

After the AC main power is restored and the battery is recharging, the DIN-LVD-48 will reconnect the load when the battery voltage exceeds 50 volts.

Features:

The Model DIN-LVD-48 is an automatic Low Voltage Disconnect that monitors battery voltage and disconnects the load when the voltage drops below 42 VDC

The DIN-LVD-48 is simple to Install and maintenance free.

Temperature Range -40°C to +70°C

3 year warranty