Type THHN-THWN-2 building wire is intended for general purpose applications and may be installed in conduit, duct, or other recognized raceways in wet (60°C oil/90°C water) or dry (105°C) locations. For both new work and rewiring applications, the smaller diameter of wire permits additional circuits or larger conductors to be installed in the conduit without exceeding maximum fill limitations. The insulation is a high quality, heat and moisture resistant polyvinyl chloride compound over which a heat and light stabilized nylon jacket is tightly applied.

FEATURES
Sunlight Resistance, Gasoline and oil resistant II, VW-1 THWN-2 or THHN or MTW (all sizes & colors), CT USE (1/0 and larger), C (UL)-Type /T90 or TWN 75, Lead Free-ROHS Compliant, 600V

Type THHN-THWN-2 building wire is intended for general purpose applications and may be installed in conduit, duct, or other recognized raceways in wet (60°C oil/90°C water) or dry (105°C) locations. For both new work and rewiring applications, the smaller diameter of wire permits additional circuits or larger conductors to be installed in the conduit without exceeding maximum fill limitations. The insulation is a high quality, heat and moisture resistant polyvinyl chloride compound over which a heat and light stabilized nylon jacket is tightly applied.

FEATURES
Sunlight Resistance, Gasoline and oil resistant II, VW-1 THWN-2 or THHN or MTW (all sizes & colors), CT USE (1/0 and larger), C (UL)-Type /T90 or TWN 75, Lead Free-ROHS Compliant, 600V

Type THHN-THWN-2 building wire is intended for general purpose applications and may be installed in conduit, duct, or other recognized raceways in wet (60°C oil/90°C water) or dry (105°C) locations. For both new work and rewiring applications, the smaller diameter of wire permits additional circuits or larger conductors to be installed in the conduit without exceeding maximum fill limitations. The insulation is a high quality, heat and moisture resistant polyvinyl chloride compound over which a heat and light stabilized nylon jacket is tightly applied.

FEATURES
Sunlight Resistance, Gasoline and oil resistant II, VW-1 THWN-2 or THHN or MTW (all sizes & colors), CT USE (1/0 and larger), C (UL)-Type /T90 or TWN 75, Lead Free-ROHS Compliant, 600V

Type THHN-THWN-2 building wire is intended for general purpose applications and may be installed in conduit, duct, or other recognized raceways in wet (60°C oil/90°C water) or dry (105°C) locations. For both new work and rewiring applications, the smaller diameter of wire permits additional circuits or larger conductors to be installed in the conduit without exceeding maximum fill limitations. The insulation is a high quality, heat and moisture resistant polyvinyl chloride compound over which a heat and light stabilized nylon jacket is tightly applied.

FEATURES
Sunlight Resistance, Gasoline and oil resistant II, VW-1 THWN-2 or THHN or MTW (all sizes & colors), CT USE (1/0 and larger), C (UL)-Type /T90 or TWN 75, Lead Free-ROHS Compliant, 600V

The NPGMT1107 Fuse Panel provides up to 20 circuits for the distribution of DC power to equipment. Each of the 20 circuits is individually protected by a GMT style telecommunication fuse located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 10 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at the rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

The NPGMT1012 Fuse Panel provides up to 30 circuits for the distribution of DC power to equipment. Each of the 30 circuits is individually protected by a GMT style telecommunication fuse (20A max) located on the panel's faceplate. Alarm circuits are provided to indicate and extend alarm conditions when faults occur. Normal Operation LEDs are provided to indicate the status of each bus in the panel.

Input wiring is connected to a high current, 2-hole lug input block located at the rear of the panel. Each group of fuses or bus has its own completely isolated inputs, allowing the distribution of two battery voltages through the same panel.

The power is distributed to the load side equipment through GMT style fuses. There are 15 fuses per fuse group and two groups per panel. Each fuse position is available for installer connection at the rear of the panel. A designation card is provided for keeping records of which position is connected to which equipment and what amperage is to be used.

The ICT DISTRIBUTION SERIES 3 provides independent dual buscapability for redundant systems or mixed-voltage sites. Eachbus is rated at 100A peak and provides six fuse or breakerprotected outputs. Standard models are available forunmanaged applications, while Intelligent models include ICT’sindustry leading TCP/IP remote management and power controlfeatures.

Features:

200A peak system current rating / 100A per bus

Six outputs per bus

Independent Form C alarm contacts for each bus

Choice of fuse or breaker protected models

80 volt rated FKS ATO style fuses or high-quality, reliablehydraulic/magnetic breakers support 12, 24 and 48VDC

Mixed voltages and polarities can be supported in one panel(provided grounds are common)

-30°C to +60°C operating temperature range

Front panel LED indicators for fuse status (fuse models)

3 year warranty